Видео

Hi, Our wet film thickness comb cannot be used in powder. However, we do supply the Elcometer 155 Uncured Powder Film Comb for this exact application! www.elcometer.com/en/elcometer-155-uncured-powder-film-comb.html

Hi, This would depend on the type of soap and its viscosity. Please get in touch with support at support@elcometer.com and we can help you with this question.

Hi, In which country are you located?

Hi, Ideally the Elcometer 456 will be calibrated at the beginning of every work day or when the coating or substrate material changes.

Hi, This would be determined by your job specification and / or your blasting sand supplier. If you have any more questions, please get in touch at support@elcometer.com

Hi, You can indeed measure curved surfaces using the Elcometer 456. It is also possible to measure the coating thickness of chrome on ferrous steel. Be sure to calibrate the gauge on an uncoated part of the cylinder. If you have any more questions, please get in touch at support@elcometer.com

@@ElcometerOfficialChannel Thank you for taking time to answer my queries

Hi, Your local distributor for India is Aimil Limited. Please click this link for their contact information to find out more on pricing and availability: www.elcometer.com/en/find-your-distributor#

Hi, If your chloride levels exceed specified limits we suggest thoroughly washing the surface using deionised water, and then repeating the test. Please ensure you are conducting the test accurately and precisely as per the video. If you have any more questions, please get in touch at support@elometer.com

Hi, The profile is typically created during the surface blasting process. Please ensure you are conducting a measurement on an appropriate surface which has been prepared as per manufacturer recommendations. If you have any more questions, please get in touch at support@elometer.com

Hi, Please ensure the sensitivity is not set to auto. We suggest starting at 50 uA and adjust accordingly on the known defect.

Hi, We suggest setting the sensitivity to manual, not automatic. Start at 50 uA and adjust as per the user manual. If you have any more questions, please get in touch at support@elometer.com

Hi, Annex A for A-1250 refers to a leak test, meaning more water must be injected. For working inspection test we advise injecting 3ml as per ISO 8502-6 If you have any more questions, please get in touch at support@elometer.com

Hi, In order to calculate Dew Point, we would suggest downloading Elcocalc, our handy app available for free on the Apple and Android app stores. If you have any more questions, please get in touch at support@elcometer.com

Thanks for the support 🙏

Hi, The Elcometer 500 is designed for concrete only coatings measurements. For coatings on forgings, we would suggest the Elcometer 456. For further technical details please get in touch at support@elcometer.com

Hi, The standard you choose should be stated in your job specification which should be agreed upon by all parties involved. Elcometer offer a list of standards to choose from, but cannot dictate which one you choose. If you have any further questions, please get in touch at support@elcometer.com

Hi, Thank you for your comment. You can apply a value on the analogue dial of -50 microns to offset the average thickness of the mylar film used on the Testex tape. If you have any further questions, please get in touch at support@elcometer.com

Hi, Thank you for your comment. We developed this kit to adhere to strict ASTM and ISO standards - ASTM D 3363 - ISO 15184:2012 Coating hardness can vary drastically. From extremely soft coatings, all the way to extremely hard coatings. This test method has been established in the industry for many years and can be suitable for a wide range of coatings. However, many more test methods do exist such as the Elcometer 3092, 3000, and 3095. If you have any further questions, please get in touch at support@elcometer.com

Hi, We supply 2-pack epoxy araldite with the gauge, however it may not be suitable for every application. We would recommend you speak with a technical representative of your local glue manufacturer. If you have any more questions, please get in touch at support@elcometer.com

Hi, Please follow this link and fill out the required information: www.elcometer.com/en/contact-us-form?type=Distributors&c=30&d=all&i=319

Hi, We are glad you like the video! We will most certainly consider delving deeper into the 266 Holiday Detector.

Hi, The Delta T needs to be greater than 3 degrees Celsius or 5 degrees Fahrenheit. If you have any more questions please get in touch at support@elcometer.com

Hi, For the information you need, the requirements of primer and coating, you are best off using your paint data sheet as reference. If you have any more questions, email support@elcometer.com

Thank you for your comment, The standard you are referring to would be the ISO 8502-4 standard. Unless otherwise agreed, the steel surface temperature should generally be at least 3 °C above the dewpoint when paints are used. If you have any other enquiries, please email support@elcometer.com and they will do their best to help.

Hi, ER4 suggest there has been a calibration failure - this is typically due to the ranges being too far out from the known calibration solutions, or possibly a sensor error. We would suggest recalibration. If this still doesn't work, please get in touch at support@elcometer.com

Hi, Please get in touch with us at support@elcometer.com and we will help you with your question.

Hi, In which country are you located?

Hi, Before you apply the dolly, we suggest ensuring the ears are pushed all of the way down (this may require some force) If you have any further questions, please get in touch at: support@elcometer.com

Thank you for your comment. The Elcometer 456 Mk4 is compatible with the new version of ElcoMaster. The full list of Elcometer gauges that are compatible can be found here under Technical Specification: www.elcometer.com/en/coatings-inspection/all-coatings-inspection/elcomaster-software/elcomaster.html

Thank you for your comment, @malarrajah. Could you please clarify on what you mean in regards to your comment?

Hi, This would depend on the extent to which you are testing it to. Typically it will leave, at the very least, a witness mark. For further information, please get in touch at techsales@elcometer.com

Hi, Yes you can so long as you use the Elcometer 108 or the Elcometer 508. We have a selection of dollies for both concave and convex surfaces. See the specifications here: Elcometer 108 (Page 11) - www.elcometer.com/media/contentmanager/content///108_instruction_english.pdf Elcometer 508 (Page 9) - downloads.elcometer.com/PDFs/InstructionManuals/MultiLingual/508.pdf And click here to see everything you need to know on adhesion: www.elcometer.com/en/coatings-inspection/all-coatings-inspection/adhesion-testers.html For further information, please get in touch at techsales@elcometer.com

Hi, Yes, you should be able to use the Surface Comparator on pipes.

Hi, We have a video explaining exactly how to do this! Please follow the link here: ruclips.net/video/5cDyhQCTWuc/видео.html If you have any further questions, please get in touch with techsales@elcometer.com

Hi, The 224 should zeroed before every job using the supplied glass slide and can be checked using the supplied shims. If a calibration certificate is required then it can be returned to Elcometer at a frequency defined by the individual’s company quality procedures. I hope this answers your question :) If you have any more questions feel free to get in touch with techsales@elcometer.com

Hi, The 415 requires a metallic substrate so will not work on wood, brick or plasterboard. If you have any more questions feel free to get in touch with techsales@elcometer.com